65 lines
2.5 KiB
Arduino
65 lines
2.5 KiB
Arduino
|
/*
|
||
|
|
* IRremoteESP8266: IRsendDemo - demonstrates sending IR codes with IRsend
|
||
|
|
* Version 0.1 June, 2015
|
||
|
|
* Based on Ken Shirriff's IrsendDemo Version 0.1 July, 2009, Copyright 2009 Ken Shirriff, http://arcfn.com
|
||
|
|
* JVC and Panasonic protocol added by Kristian Lauszus (Thanks to zenwheel and other people at the original blog post)
|
||
|
|
*
|
||
|
|
* An IR LED circuit *MUST* be connected to ESP8266 pin 4 (D2).
|
||
|
|
*
|
||
|
|
* TL;DR: The IR LED needs to be driven by a transistor for a good result.
|
||
|
|
*
|
||
|
|
* Suggested circuit:
|
||
|
|
* https://github.com/markszabo/IRremoteESP8266/wiki#ir-sending
|
||
|
|
*
|
||
|
|
* Common mistakes & tips:
|
||
|
|
* * Don't just connect the IR LED directly to the pin, it won't
|
||
|
|
* have enough current to drive the IR LED effectively.
|
||
|
|
* * Make sure you have the IR LED polarity correct.
|
||
|
|
* See: https://learn.sparkfun.com/tutorials/polarity/diode-and-led-polarity
|
||
|
|
* * Typical digital camera/phones can be used to see if the IR LED is flashed.
|
||
|
|
* Replace the IR LED with a normal LED if you don't have a digital camera
|
||
|
|
* when debugging.
|
||
|
|
* * Avoid using the following pins unless you really know what you are doing:
|
||
|
|
* * Pin 0/D3: Can interfere with the boot/program mode & support circuits.
|
||
|
|
* * Pin 1/TX/TXD0: Any serial transmissions from the ESP8266 will interfere.
|
||
|
|
* * Pin 3/RX/RXD0: Any serial transmissions to the ESP8266 will interfere.
|
||
|
|
* * ESP-01 modules are tricky. We suggest you use a module with more GPIOs
|
||
|
|
* for your first time. e.g. ESP-12 etc.
|
||
|
|
*/
|
||
|
|
|
||
|
|
#ifndef UNIT_TEST
|
||
|
|
#include <Arduino.h>
|
||
|
|
#endif
|
||
|
|
#include <IRremoteESP8266.h>
|
||
|
|
#include <IRsend.h>
|
||
|
|
|
||
|
|
#define PanasonicAddress 0x4004 // Panasonic address (Pre data)
|
||
|
|
#define PanasonicPower 0x100BCBD // Panasonic Power button
|
||
|
|
|
||
|
|
#define JVCPower 0xC5E8
|
||
|
|
|
||
|
|
IRsend irsend(4); // An IR LED is controlled by GPIO pin 4 (D2)
|
||
|
|
|
||
|
|
void setup() {
|
||
|
|
irsend.begin();
|
||
|
|
}
|
||
|
|
|
||
|
|
void loop() {
|
||
|
|
// This should turn your TV on and off
|
||
|
|
#if SEND_PANASONIC
|
||
|
|
irsend.sendPanasonic(PanasonicAddress, PanasonicPower);
|
||
|
|
#else // SEND_PANASONIC
|
||
|
|
Serial.println("Can't send because SEND_PANASONIC has been disabled.");
|
||
|
|
#endif // SEND_PANASONIC
|
||
|
|
|
||
|
|
#if SEND_JVC
|
||
|
|
irsend.sendJVC(JVCPower, 16, 0); // hex value, 16 bits, no repeat
|
||
|
|
// see http://www.sbprojects.com/knowledge/ir/jvc.php for information
|
||
|
|
delayMicroseconds(50);
|
||
|
|
irsend.sendJVC(JVCPower, 16, 1); // hex value, 16 bits, repeat
|
||
|
|
delayMicroseconds(50);
|
||
|
|
#else // SEND_JVC
|
||
|
|
Serial.println("Can't send because SEND_JVC has been disabled.");
|
||
|
|
#endif // SEND_JVC
|
||
|
|
}
|