69 lines
2.6 KiB
Arduino
69 lines
2.6 KiB
Arduino
|
/* IRremoteESP8266: IRsendDemo - demonstrates sending IR codes with IRsend.
|
||
|
*
|
||
|
* Version 1.0 April, 2017
|
||
|
* Based on Ken Shirriff's IrsendDemo Version 0.1 July, 2009,
|
||
|
* Copyright 2009 Ken Shirriff, http://arcfn.com
|
||
|
*
|
||
|
* An IR LED circuit *MUST* be connected to ESP8266 pin 4 (D2).
|
||
|
*
|
||
|
* TL;DR: The IR LED needs to be driven by a transistor for a good result.
|
||
|
*
|
||
|
* Suggested circuit:
|
||
|
* https://github.com/markszabo/IRremoteESP8266/wiki#ir-sending
|
||
|
*
|
||
|
* Common mistakes & tips:
|
||
|
* * Don't just connect the IR LED directly to the pin, it won't
|
||
|
* have enough current to drive the IR LED effectively.
|
||
|
* * Make sure you have the IR LED polarity correct.
|
||
|
* See: https://learn.sparkfun.com/tutorials/polarity/diode-and-led-polarity
|
||
|
* * Typical digital camera/phones can be used to see if the IR LED is flashed.
|
||
|
* Replace the IR LED with a normal LED if you don't have a digital camera
|
||
|
* when debugging.
|
||
|
* * Avoid using the following pins unless you really know what you are doing:
|
||
|
* * Pin 0/D3: Can interfere with the boot/program mode & support circuits.
|
||
|
* * Pin 1/TX/TXD0: Any serial transmissions from the ESP8266 will interfere.
|
||
|
* * Pin 3/RX/RXD0: Any serial transmissions to the ESP8266 will interfere.
|
||
|
* * ESP-01 modules are tricky. We suggest you use a module with more GPIOs
|
||
|
* for your first time. e.g. ESP-12 etc.
|
||
|
*/
|
||
|
|
||
|
#ifndef UNIT_TEST
|
||
|
#include <Arduino.h>
|
||
|
#endif
|
||
|
#include <IRremoteESP8266.h>
|
||
|
#include <IRsend.h>
|
||
|
|
||
|
IRsend irsend(4); // An IR LED is controlled by GPIO pin 4 (D2)
|
||
|
|
||
|
// Example of data captured by IRrecvDumpV2.ino
|
||
|
uint16_t rawData[67] = {9000, 4500, 650, 550, 650, 1650, 600, 550, 650, 550,
|
||
|
600, 1650, 650, 550, 600, 1650, 650, 1650, 650, 1650,
|
||
|
600, 550, 650, 1650, 650, 1650, 650, 550, 600, 1650,
|
||
|
650, 1650, 650, 550, 650, 550, 650, 1650, 650, 550,
|
||
|
650, 550, 650, 550, 600, 550, 650, 550, 650, 550,
|
||
|
650, 1650, 600, 550, 650, 1650, 650, 1650, 650, 1650,
|
||
|
650, 1650, 650, 1650, 650, 1650, 600};
|
||
|
|
||
|
void setup() {
|
||
|
irsend.begin();
|
||
|
Serial.begin(115200, SERIAL_8N1, SERIAL_TX_ONLY);
|
||
|
}
|
||
|
|
||
|
void loop() {
|
||
|
#if SEND_NEC
|
||
|
Serial.println("NEC");
|
||
|
irsend.sendNEC(0x00FFE01FUL, 32);
|
||
|
#endif // SEND_NEC
|
||
|
delay(2000);
|
||
|
#if SEND_SONY
|
||
|
Serial.println("Sony");
|
||
|
irsend.sendSony(0xa90, 12, 2);
|
||
|
#endif // SEND_SONY
|
||
|
delay(2000);
|
||
|
#if SEND_RAW
|
||
|
Serial.println("a rawData capture from IRrecvDumpV2");
|
||
|
irsend.sendRaw(rawData, 67, 38); // Send a raw data capture at 38kHz.
|
||
|
#endif // SEND_RAW
|
||
|
delay(2000);
|
||
|
}
|